Welcome

 Call us to speak with a representative (972 ) 494-3300

 
Credit Application Form FAQ Warranty Information About Us Jobs

Back to Top

HP LASERJET ERROR CODES 60 AND UP

HP LASERJET ERROR CODES 60 AND UP

 

Message on printer Display Panel

What it means.

What to do.

Additional comments.

62.X PRINTER ERROR

There is a problem with the printer memory. The X value refers to the location of the problem: 0 = Internal memory 1 to 4 = DIMM slots 1, 2, 3, or 4

1. Reseat the specified DIMM. 2. Replace the specified DIMM

 

64 PRINTER ERROR alternates with CYCLE POWER

A scan buffer error occurred

1. Turn the printer off, and then turn the printer on. 2. Perform a cold reset. 3. If the message persists, replace the formatter or firmware DIMM.

 

66.XX.YY [TYPE] FAILURE alternates with CHECK CABLES AND CYCLE POWER

An error occurred in an external paper-handling device. 1st X = Device number in chain 2nd X = Device type 1 Input 2 Output 3 Stapler/stacker unit YY = Device specific error

Press GO to clear the message. If the message will not clear: 1. Turn the printer off, and then turn the printer on. 3. Check and reseat all cables between the printer and the specified device. 4. Reseat the external paperhandling device. 5. Replace the unit.

On 5si, 8000, 8100 check the C-link hook up. Also check the external paper handling PCA.

68 NVRAM ERROR CHECK SETTINGS

An error occurred in the printer non-volatile memory (NVRAM) and one or more printer settings has been reset to its factory default

1. Print a configuration page and check the printer settings to determine which values have changed. 2. Hold down CANCEL JOB while turning the printer on. This will clean up the NVRAM by removing old areas that are not being used. 3. Replace the formatter.

 

68 NVRAM FULL CHECK SETTINGS

An error occurred in the printer’s NVRAM and one or more printer settings has been reset to its factory default.

1. Print a configuration page and check the printer settings to determine which values have changed. 2. Hold down CANCEL JOB while turning the printer on. This will clean up the NVRAM by removing old areas that are not being used.

 

68.X PERMANENT STORAGE ERROR alternates with CHECK SETTINGS

An error occurred in the printer’s permanent storage and one or more printer settings has been reset to its factory default.

Print a configuration page and check the printer settings to determine which values have changed.

 

68.X PERMANENT STORAGE FULL

The printer’s permanent storage is full. Some settings might have been reset to the factory defaults.

1. Print a configuration page and check the printer settings to determine which values have changed. 2. Hold down CANCEL JOB while turning the printer on. This will clean up the permanent storage by removing old areas that are not being used.

 

69.X PRINTER ERROR alternates with CYCLE POWER TO CONTINUE

A temporary printing error occurred. X description: 0 = The duplex mechanism has failed

1. Turn the printer off, and then turn the printer on. 2. Reseat the duplexer. 3. Replace the duplexer

 

79 SERVICE [XXXX]

The printer detected an error.

1. Press CANCEL JOB to clear the print job from the printer memory. 2. Turn the printer off, and then turn the printer on. 3. Try printing a job from a different software application. If the job prints, go back to the first application and try printing a different file. (If the message only appears with a certain software application or print job, contact the software vendor for assistance.) 4. If the message persists with different software applications and print jobs, disconnect all cables to the printer that connect it to the network or printer. 5. Turn the printer off. 6. Remove all memory DIMMs or third-party DIMMs from the printer. (Do not remove the firmware DIMM in the lowest DIMM slot.) 7. Remove all EIO devices from the printer. 8. Turn the printer on. 9. If the error no longer exists, install each DIMM and EIO device one at a time, making sure to turn the printer off and back on as you install each device. 10. Replace a DIMM or EIO device if you determine that it causes the error. 11. Remember to reconnect all cables that connect the printer to the network or computer. 12. If the error persists, replace the firmware DIMM. 13. Replace the formatter.

 

79 & 80 errors - general info.

For trouble shooting 79 and 80 errors you want to determine if external I/O devices are the cause or if it is the formatter.

Remove all external I/O devices (JetDirect, memory, etc.) and see if problem persists. If not, replace the formatter.

 

8X.YYYY EIO [Z] ERROR

The EIO accessory in slot [z] has encountered a critical error. [z] description: 1 = EIO slot 1—The printer detected an error with the EIO accessory. 2 = EIO slot 2—The printer detected an error with the EIO accessory. 6 = EIO slot 1—The EIO accessory detected an error. 7 = EIO slot 2—The EIO accessory detected an error.

1. Turn the printer off, and then turn the printer on. 2. Turn the printer off, reseat the EIO accessory in slot [z], and then turn the printer on. 3. Turn the printer off, remove the EIO accessory from slot [z], install it in a different EIO slot, and turn the printer on. 4. Replace the EIO accessory in slot [z].